HASSIO 安装一键脚本

neroxps

bossben8 发表于 2020-10-10 18:28
See "systemctl status auditd.service" and "journalctl -xe" for details.
invoke-rc.d: initscript audi ...

https://bbs.hassbian.com/forum.p ... 4520&pid=341787

树莓派安装 auditd 都是这样的，我没有树莓派，请自行解决。

huasangsang

树莓派必须去掉 network-manager 依赖才能正常安装...不然会死机,重启后MAC也会随机变更..

neroxps

huasangsang 发表于 2020-10-10 22:08
树莓派必须去掉 network-manager 依赖才能正常安装...不然会死机,重启后MAC也会随机变更.. ...

官方脚本默认就必须要装 https://github.com/home-assistan ... ea/installer.sh#L61

我也没树莓派，如果知道的可以PR 下解决办法。

huasangsang

neroxps 发表于 2020-10-10 22:28
官方脚本默认就必须要装 https://github.com/home-assistant/supervised-installer/blob/93c6cb330e5fefa ...

可以连接网线, 手动安装NetworkManager,然后干掉原来的网络管理,然后手动分配一个静态IP

huasangsang

neroxps 发表于 2020-10-10 22:28
官方脚本默认就必须要装 https://github.com/home-assistant/supervised-installer/blob/93c6cb330e5fefa ...

连接网线后:
1. 使用 sudo apt install network-manager network-manager-gnome  安装networkManager
2. 重启一次树莓派, 去路由器里看一下新分配的IP,使用新IP连接树莓派
3. 卸载原来的服务 sudo apt purge openresolv dhcpcd5 , 再重启一次
4. 去路由器里看一下新分配的IP,使用新IP连接树莓派
5. 使用 sudo ifconfig wlan0 down 命令关掉wifi, 使用 sudo ifconfig eth0 hw ether "你原来分配好的MAC" 分配MAC地址, 使用 sudo ifconfig eth0 up 命令启动wifi
6. 使用  nmcli device wifi connect <wifi名> password <密码> 连接wifi
7. 把上面的命令加入开机启动,具体方法百度.

qlql0101

Master 发表于 2020-10-8 16:52
After this operation, 0 B of additional disk space will be used.
Setting up auditd (1:2.8.4-3) ...
J ...

https://bbs.hassbian.com/forum.p ... 4520&pid=342362

bossben8

qjiang 发表于 2020-9-14 15:04
dpkg: 处理软件包 xxx (--configure)时出错 解决办法

第一步：备份

正想發文就找到此篇.....沒錯我就是按照此步驟後再執行安裝腳本解決無法安裝的問題.........

neroxps

huasangsang 发表于 2020-10-10 23:37
连接网线后:
1. 使用 sudo apt install network-manager network-manager-gnome  安装networkManager
2.  ...

好复杂····还是留给用户自己选择吧。如果不会操作还是自己装 hassos

zs1024242524

huasangsang 发表于 2020-10-10 23:37
连接网线后:
1. 使用 sudo apt install network-manager network-manager-gnome  安装networkManager
2.  ...

需要加入开机启动的命令有哪些

zs1024242524

Unpacking socat (1.7.3.2-2) ...
Setting up python3-libapparmor (2.13.2-10) ...
Setting up libqrencode4:armhf (4.0.2-1) ...
Setting up qrencode (4.0.2-1) ...
Setting up libcurl3-gnutls:armhf (7.64.0-4+deb10u1) ...
Setting up dnsmasq-base (2.80-1+rpt1) ...
Setting up libauparse0:armhf (1:2.8.4-3) ...
Setting up libjansson4:armhf (2.12-1) ...
Setting up dns-root-data (2019031302) ...
Setting up apparmor (2.13.2-10) ...
Created symlink /etc/systemd/system/sysinit.target.wants/apparmor.service → /lib/systemd/system/apparmor.service.
Setting up libpcap0.8:armhf (1.8.1-6) ...
Setting up libteamdctl0:armhf (1.28-1) ...
Setting up socat (1.7.3.2-2) ...
Setting up libnm0:armhf (1.14.6-2+deb10u1) ...
Setting up ppp (2.4.7-2+4.1+deb10u1) ...
Created symlink /etc/systemd/system/multi-user.target.wants/pppd-dns.service → /lib/systemd/system/pppd-dns.service.
Setting up libmm-glib0:armhf (1.10.0-1) ...
Setting up libbluetooth3:armhf (5.50-1.2~deb10u1+rpt2) ...
Setting up python3-apparmor (2.13.2-10) ...
Setting up libndp0:armhf (1.6-1) ...
Setting up libonig5:armhf (6.9.1-1) ...
Setting up libgudev-1.0-0:armhf (232-2+rpi1) ...
Setting up libmbim-glib4:armhf (1.18.0-1) ...
Setting up auditd (1:2.8.4-3) ...
Created symlink /etc/systemd/system/multi-user.target.wants/auditd.service → /lib/systemd/system/auditd.service.
Job for auditd.service failed because the control process exited with error code.
See "systemctl status auditd.service" and "journalctl -xe" for details.
invoke-rc.d: initscript auditd, action "start" failed.
● auditd.service - Security Auditing Service
   Loaded: loaded (/lib/systemd/system/auditd.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Sun 2020-10-18 10:55:54 BST; 23ms ago
     Docs: man:auditd(8)
           https://github.com/linux-audit/audit-documentation
  Process: 1649 ExecStart=/sbin/auditd (code=exited, status=1/FAILURE)

Oct 18 10:55:54 raspberrypi systemd[1]: Starting Security Auditing Service...
Oct 18 10:55:54 raspberrypi auditd[1650]: Error - audit support not in kernel
Oct 18 10:55:54 raspberrypi auditd[1650]: Cannot open netlink audit socket
Oct 18 10:55:54 raspberrypi auditd[1650]: The audit daemon is exiting.
Oct 18 10:55:54 raspberrypi auditd[1649]: Cannot daemonize (Success)
Oct 18 10:55:54 raspberrypi systemd[1]: auditd.service: Control process exited, code=exited, status=1/FAILURE
Oct 18 10:55:54 raspberrypi auditd[1649]: The audit daemon is exiting.
Oct 18 10:55:54 raspberrypi systemd[1]: auditd.service: Failed with result 'exit-code'.
Oct 18 10:55:54 raspberrypi systemd[1]: Failed to start Security Auditing Service.
dpkg: error processing package auditd (--configure):
installed auditd package post-installation script subprocess returned error exit status 1
Setting up libjq1:armhf (1.5+dfsg-2+b1) ...
Setting up network-manager (1.14.6-2+deb10u1) ...
Created symlink /etc/systemd/system/dbus-org.freedesktop.nm-dispatcher.service → /lib/systemd/system/NetworkManager-dispatcher.service.
Created symlink /etc/systemd/system/network-online.target.wants/NetworkManager-wait-online.service → /lib/systemd/system/NetworkManager-wait-online.service.
Created symlink /etc/systemd/system/multi-user.target.wants/NetworkManager.service → /lib/systemd/system/NetworkManager.service.
Setting up libmbim-proxy (1.18.0-1) ...
Setting up apparmor-utils (2.13.2-10) ...
Setting up jq (1.5+dfsg-2+b1) ...
Setting up libqmi-glib5:armhf (1.22.0-1.2) ...
Setting up libqmi-proxy (1.22.0-1.2) ...
Setting up modemmanager (1.10.0-1) ...
Created symlink /etc/systemd/system/dbus-org.freedesktop.ModemManager1.service → /lib/systemd/system/ModemManager.service.
Created symlink /etc/systemd/system/multi-user.target.wants/ModemManager.service → /lib/systemd/system/ModemManager.service.
Processing triggers for systemd (241-7~deb10u4+rpi1) ...
Processing triggers for man-db (2.8.5-2) ...
Processing triggers for dbus (1.12.20-0+deb10u1) ...
Processing triggers for libc-bin (2.28-10+rpi1) ...
Errors were encountered while processing:
auditd
E: Sub-process /usr/bin/dpkg returned an error code (1)

################# 发到论坛时，请把上方日志也一并粘贴发送 ################
########################### System version ###########################
Distributor ID: Raspbian
Description:    Raspbian GNU/Linux 10 (buster)
Release:        10
Codename:       buster
########################### System version 2 ###########################
Linux version 5.4.51-v7l+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1333 SMP Mon Aug 10 16:51:40 BST 2020
########################### System info ###########################
Linux raspberrypi 5.4.51-v7l+ #1333 SMP Mon Aug 10 16:51:40 BST 2020 armv7l GNU/Linux
########################### END ###########################
\033[0;31m[ERROR]: 安装curl失败，请将检查上方安装错误信息。\033[0m

相关问题可以访问https://bbs.iobroker.cn或者加QQ群776817275咨询