利用zigbee模块DIY一个万能zigbee网关

MAPGPS · 发表于 2019-4-5 19:07:20

淘了个树莓派3B+，与CC2531 zigbee USB组成了zigbee网关。

zigbee2mqtt可以检测到我的云米智能门锁，但报告还未支持。
回头改改代码，让其支持云米智能门锁。

  zigbee2mqtt:info 4/5/2019, 6:33:59 PM New device 'undefined' with address 0x00158d0002acxxxx connected!
  zigbee2mqtt:info 4/5/2019, 6:33:59 PM MQTT publish: topic 'zigbee2mqtt/bridge/log', payload '{"type":"device_connected","message":"0x00158d0002acxxxx","meta":{}}'
  zigbee2mqtt:warn 4/5/2019, 6:33:59 PM Device with modelID 'undefined' is not supported.
  zigbee2mqtt:warn 4/5/2019, 6:33:59 PM Please see: [url]https://www.zigbee2mqtt.io/how_tos/how_to_support_new_devices.html[/url]
  zigbee2mqtt:info 4/5/2019, 6:34:02 PM Device incoming...
  zigbee2mqtt:info 4/5/2019, 6:34:02 PM MQTT publish: topic 'zigbee2mqtt/bridge/log', payload '{"type":"pairing","message":"device incoming"}'
  zigbee2mqtt:warn 4/5/2019, 6:34:02 PM Device with modelID 'FNB56-DOR23FB1.3' is not supported.
  zigbee2mqtt:warn 4/5/2019, 6:34:02 PM Please see: [url]https://www.zigbee2mqtt.io/how_tos/how_to_support_new_devices.html[/url]

MAPGPS · 发表于 2019-4-5 19:13:01

本帖最后由 MAPGPS 于 2019-4-5 19:16 编辑

我的zigbee网关： CC2531 + 树莓派3B+

MAPGPS · 发表于 2019-4-7 11:35:39

修改了一下代码，可以支持云米智能门锁的开锁信息通知了。
这是zigbee2mqtt的debug log：

老妈 (刷手机):
4/7/2019, 10:45:32 AM - debug: Received zigbee message of type 'cmdOperationEventNotification' with data '{"cid":"closuresDoorLock","data":{"opereventsrc":3,"opereventcode":2,"userid":2,"pin":0,"zigbeelocaltime":0,"data":1}}' of device 'FNB56-DOR23FB1.3' (0x00158d0002acxxxx)
我 (指纹):
4/7/2019, 10:46:14 AM - debug: Received zigbee message of type 'cmdOperationEventNotification' with data '{"cid":"closuresDoorLock","data":{"opereventsrc":2,"opereventcode":2,"userid":2,"pin":0,"zigbeelocaltime":0,"data":1}}' of device 'FNB56-DOR23FB1.3' (0x00158d0002acxxxx)
老婆 (刷手机):
4/7/2019, 10:46:51 AM - debug: Received zigbee message of type 'cmdOperationEventNotification' with data '{"cid":"closuresDoorLock","data":{"opereventsrc":3,"opereventcode":2,"userid":1,"pin":0,"zigbeelocaltime":0,"data":1}}' of device 'FNB56-DOR23FB1.3' (0x00158d0002acxxxx)

其中：opereventsrc = 2（指纹），3（刷手机），4（远程）

再研究一下怎么t通过HA发送远程开锁命令。