请大神帮忙写写配置文件

chenggangyaan

本人代码小白，最近研究自制zigbee网关，综合大神教程，现在搞出了一个利用tasmota（zigbee.bin）连接CC2530,现在已经成功将设备接入，能在tasmota webui里面看到设备（命令窗口能看到设备各种信息），mqtt配置到了homeassistant。但是现在不知道怎么在homeassistant里面写配置文件，将设备信息读取出来，比如人体感应器（想获取：状态、电量、信号强度）等。希望大神能指导一二。   获取的信息如下。

MQT: tele/z2m/SENSOR = {"ZbReceived":{"0x987E":{"Device":"0x987E","Name":"涂鸦感应器","BatteryVoltage":3,"BatteryPercentage":100,"Endpoint":1,"LinkQuality":148}}}
MQT: tele/z2m/SENSOR = {"ZbReceived":{"0x076B":{"Device":"0x076B","Name":"无线开关","BatteryVoltage":2.99,"BatteryPercentage":96,"Endpoint":1,"LinkQuality":171}}}

chenggangyaan

sensor:
  - platform: mqtt
    name: 感应器电量
    state_topic: "tele/z2m/SENSOR/0x987E"  
    value_template: "{{ value_json.BatteryPercentage }}"
    unit_of_measurement: "%"
    qos: 0
    device_class: battery

  - platform: mqtt
    name: 信号强度
    state_topic: "tele/z2m/SENSOR/0x987E"  
    value_template: "{{ value_json.LinkQuality }}"
    qos: 0
    device_class: signal_strength

chenggangyaan

这是我目前的代码，但是这样在homeassistant中获取不到任何信息，请高人指导一下，十分感谢！

dscao

sensor:
  - platform: mqtt
    name: 感应器电量
    state_topic: "tele/z2m/SENSOR"  
    value_template: "{{ value_json['ZbReceived']['0x987E'].BatteryPercentage }}"
    unit_of_measurement: "%"
    qos: 0
    device_class: battery

这样试试……
value_template: "{{ value_json['ZbReceived']['0x987E']['BatteryPercentage'] }}"

value_template: "{{ value_json.ZbReceived.0x987E.BatteryPercentage }}"

不行也试试吧，也不太分得清用哪个。

chenggangyaan

dscao 发表于 2021-8-22 22:34
sensor:
  - platform: mqtt
    name: 感应器电量

非常感谢，安装您的第一种方法，成功将信息接入homeassistant。但是有一个问题需要请教，人体感应器在tasmota命令窗口有人显示："ZoneStatus":1，没人："ZoneStatus":0，这种的mqtt配置又该怎么写，在homeassistant里面才能显示人体感应器的图标及动作呢

chenggangyaan

已经搞定了，贴一下成功配置，供需要的人参考：
sensor:
   - platform: mqtt
    name: 感应器信号强度
    state_topic: "tele/z2m/SENSOR"  
    value_template: "{{ value_json['ZbReceived']['0x987E'].LinkQuality }}"
    qos: 0
    device_class: signal_strength
   
  - platform: mqtt
    name: 感应器电量
    state_topic: "tele/z2m/SENSOR"  
    value_template: "{{ value_json['ZbReceived']['0x987E'].BatteryPercentage }}"
    unit_of_measurement: "%"
    qos: 0
    device_class: battery     
   
binary_sensor:
  - platform: mqtt
    name: 感应器
    state_topic: "tele/z2m/SENSOR"  
    value_template: "{{ value_json['ZbReceived']['0x987E'].ZoneStatus }}"
    payload_on: "1"    payload_off: "0"
    qos: 1   
    device_class: motion